Fullscreen
FiberTEK IV

FiberTEK IV

  • Troubleshooting: Red laser light source to visually pinpoint faults and locate fibre ports
  • Receive LED indicator: Flashes red to warn of light from other sources, green when linked to FiberTEK IV
  • Certification: Tier-1 certification of single-mode and multimode fibre optic cabling
  • Encircled Flux compliance: Enables compliance to the 2016 fibre standards IEC 14763-3 and ANSI/TIA- 526- 14-C (optional accessory – see back page for details)
  • Field calibration: Allows 1 and 3 jumper field calibration methods to ensure accuracy and compliance to ISO/IEC and ANSI/TIA standards
  • Supports all common connector types: SC, FC, ST adapters included. LC adapters optional
  • Simplified bi-directional measurements: Eliminates process of manually merging directional tests into one record

Description

FiberTEK IV adapters are used with LanTEK IV-S for fast and simple certification of high bandwidth single-mode and multimode fibre optic cabling including support for encircled flux testing.

FiberTEK IV Optional Accessories

Part No Descriptions
R164050 FT III/IV-Encircled Flux 50/125um Cable SC – SC
R164051 FT III/IV-Encircled Flux 50/125um Cable SC – LC
R164064 FTIII/IV – LC Receiver Adapter (Single)

Sapphire Care Plans for FiberTEK III/IV

Part No Descriptions
SCP1YF Sapphire Care Plan – Fibre (Per Pair) – 1 Year
SCP2YF Sapphire Care Plan – Fibre (Per Pair) – 2 Years
SCP3YF Sapphire Care Plan – Fibre (Per Pair) – 3 Years

Included: Free repairs, free annual calibration, free loan tester during repairs and calibration, free shipping, free firmware updates, free technical support, free replaceable wear parts. Terms and conditions apply.

*when purchased within 60 days of purchasing a new LanTEK IV-S.

 

Additional information

Part No R164008

FiberTEK IV-MM LED Kit. Two multimode FiberTEK IV modules, lockable semi-rigid carrying case, SC, FC, ST adapters for modules (2 ea.), SC-SC patch cords, 6x 9μm MMF) compliant to ISO/IEC 14763-3 standard, quick reference guide. Compatible with LanTEK IV-S.
Part No R164009

FiberTEK IV-SM Laser Kit. Two single-mode FiberTEK IV modules, lockable semi-rigid carrying case, SC, FC, ST adapters for modules (2 ea.), SC-SC patch cords, 6x 50μm MMF) compliant to ISO/IEC 14763-3 standard, quick reference guide. Compatible with LanTEK IV-S.
Part No R164010

FiberTEK IV-MM LED & SM Laser Kit. Two multimode FiberTEK IV modules, two single-mode FiberTEK IV modules, lockable semi-rigid carrying case, SC, FC, ST adapters for modules (2 ea.), SC-SC patch cords, 6 x 9μm, 6 x 50μm compliant to ISO/IEC 14763-3 standard, quick reference guide. Compatible with LanTEK IV-S.

Related products

  • NaviTEK NT

    NaviTEK NT
    • Port & network summary info: Press the Autotest button to display summary information and allow for detailed inspection of network parameters
    • VLAN detection & operation: Automatic detection of VLAN ID’s allows the user to configure NaviTEK NT for operation on a VLAN
    • Ethernet utilisation: Real time display of broadcast network traffic shown as a percentage of port speed for the previous 60 minutes
    • CDP/LLDP/EDP port information: Show port information using Cisco Discovery Protocol (CDP), Link Layer Discovery Protocol (LLDP) and Extreme Discovery Protocol (EDP)
    • Netscan: Display list of IP and MAC addresses of every device connected to the network
    • Network Probe: View network illustration to verify test results of each network component
    Read more
  • VFF5

    VFF5
    • A hand-held, batterypowered tool, the VFF5 projects a highly visible red light into a fibre optic cable. The VFF5 is used to check continuity of cabling between termination points and to locate bends or breaks in fibres at splicing and termination points
    • Useful over a distance of approximately 5km (3.1mi) into multimode fibre and single-mode fibre. Use it as a stand-alone first-line basic troubleshooting tool, or in conjunction with an OTDR to pinpoint faults. Any breaks will be seen as a conspicuously glowing or blinking red light area (in 3mm or smaller cables)
    • Equipped with a highpower, day light visible 650nm laser diode which operates either in continuous or flashing mode. The design prevents battery drain due to accidental activation of the tool while inside a tool pouch
    • Packaged in a pocket-sized, rugged metal housing and is fitted with 2.5 mm universal connector that accepts ST, SC and FC optical connectors
    Read more
  • NaviTEK IE

    NaviTEK IE
    • Pinpoint cable faults on copper and fibre cabling
    • Easily configure nodes to resolve connectivity issues
    • Prevent network failures with the health check feature
    • Locate hard to find devices using the device blink feature
    • Find mis-configured devices using the NetMAP comparison tool
    • Find rogue devices using the 48 hour event log
    • Create professional PDF reports for your clients
    • Send reports anywhere using the free TREND AnyWARE app
    Read more
  • SignalTEK CT

    SignalTEK CT
    • Fast Autotest provides proof of network performance in seconds
    • Support for shielded and unshielded twisted pair cable including Cat 5e, Cat 6, Cat 6A and Cat 7
    • Stores up to 5000 tests to accommodate even the largest jobs
    • Identify and trace cables with a compatible amplifier probe (R180001)
    • Automatic generation of PDF test reports makes documentation effortless
    • Tests against IEEE802.3ab to assure cable performance against a recognised international standard
    • No requirement for annual calibration reducing cost of ownership
    • Field replaceable RJ45 contacts eliminate downtime from worn or damaged connectors
    Read more